FREE SHIPPING OVER $20
Free Shipping Inside The USA
MONEY BACK GUARANTEE
30-Day Money Back Guarantee.
MADE IN THE USA
100% American Made Products.
CoverSeal AC30 Matte Wood Floor/Laminated, Low Sheen Sealer
- Location : Interior/Exterior
- Task : Floor/Deck
- Application : Micro-fiber flat mop
- Base : Water Based Acrylic
- Coverage : 450-500 ft² / gal
- Finish : Matte
- Secure Checkout
- Location : Interior/Exterior
- Task : Floor/Deck
- Application : Micro-fiber flat mop
- Base : Water Based Acrylic
- Coverage : 450-500 ft² / gal
- Finish : Matte
Delivery Time: Typically 3 to 5 business days
- Description
- Technical
- Reviews
Description
CoverSeal AC30 Durable, Fast Setting, Water based UV Resistant Sealer
CoverSeal AC30 is tough fast setting water based acrylic
sealer for wood, tile, terrazzo and other hard surface
flooring. When cured the product will produce a hard
wearing clear bright surface that provides protection
against stains and exceptional water resistance.
Features:
- UV resistant non yellowing sealer
- Low odor
- Fast drying
- Breathable
- Highly water repellent
- Beautifies and protects faded surfaces
- Mold and Mildew resistant
- Repels, oil, grease and rust stains
- Voc compliant
- Abrasion resistant
- Makes surface easier to clean
Typical Uses:
- Hard wood flooring
- Plywood
- Wood laminate
- Bamboo
- Wood Decks
- VCT
- Concrete
- Terrazzo
- Quarry Tile
- Saltillo Tile
- Natural stone
- Exterior and Interior
Finish
Dries Water Clear. Matte or Gloss
Packaging
5 gallon (19 liter) pail and 1 gallon (3.8 liter) jug.
Shelf Life
12 months when stored at 77°F (25°C) or less in a dry
and shaded area. Protect from freezing.
Theoretical Coverage
Approximately 1200 to 1800 ft²/gal (29.4 – 44.0 m²/liter)
per coat. The actual cover will vary depending on the
texture and porosity of the substrate.
A two-coat application is recommended.
Appplication Properties
| Property | Typical Results |
|---|---|
| Solids by weight | 25% |
| VOG | 123 g/l |
| Tack Free | 30 to 45 minutes |
| Recoat Time | 1.0 to 2 hours |
| Light foot traffic | 2.0 to 4 hours |
| Heavy Foot Traffic | 8.0 to 12 hours |
| Odor | Very mild |
Surface Preparation
Wood
CoverSeal AC30 is compatible over most existing wood
finishes that are in good condition and intact. Use
SurfaceTreat cleaner over any floor wax. Contact
CoverTec representative to check compatibility.
Substrate shall be free of oil, dust, dirt, grease, or flaking
sealer before sand screening. Lightly screen surface
with 120 grit paper to achieve a roughened surface. After
sand screening the surface, remove all dust and debris.
Wood Laminate
CoverSeal AC30 will adhere to most wood laminate
after proper preparation. Be certain floor is free from
all wax or oily residue. Clean and abrade floor with 120
grit sandpaper. Do not use steel wool. Vacuum
thoroughly and tack floor with a slightly water-dampened
cloth to remove all dust.
Always prepare a sample or test area to determine
compatibility.
Concrete, terrazzo, stone and tile
The surface must be completely free of oil, grease,
curing compounds, other coatings, water repellants and
any other foreign material that may inhibit the sealer
adhesion to it. The surface must be porous enough to
allow sealer penetration.
Use SurfaceTreat for Deep cleaning existing finish without stripping. Dilute 8fl.oz per 1 gallon of cold water.Use a heavy-duty hair pad under a low-speed machine orautomatic scrubber to deeply cleanse the finish (will not strip finish). Clean up to 4 layers deep. Scrub floor and pick up the solution in one pass or damp-mop thoroughly. Let it dry. Apply 2 coats of AC30.
Test for water absorption. If water beads on any section of
the floor repeat the process until contaminants are
completely removed. After cleaning, allow surface to dry
24 hours prior to sealer application. Allow new concrete to cure for at least 14 days before application.
Mixing
Stir CoverSeal AC30 thoroughly before use.
Application CoverSeal AC30 may be applied by may be applied via TBar, micro-fiber applicator, short nap roller (1/4” to 3/8” nap), or low-pressure sprayer. Apply two or more thin coats. Allow to dry tack free between coats. AC30 responds to immediate follow-up buffing and burnishing.
Dry time is approximately 30 mins at 70°F (21°C), but varies depending on temperature, wind and humidity.
Wood Flooring Use a synthetic bar applicator to provide the smoothest finish. Best results are achieved when ambient temperatures are between 50 and 90 F, and humidity below 80%.
Pour a 5 – 6″ wide line of finish along the starting wall, going with the grain of the wood.
Using a clean, dampened applicator, draw the finish toward the opposite wall going with the grain of the wood. Holding the applicator at a “snowplow” angle will maintain a wet edge at all times. As you approach the end of the run, turn the applicator toward you and pad out excess material parallel to the wet edge. Feather out all turns.
Dry Time
Protect the application from rain for 12 hours. Light foot
traffic is possible after 2 to 4 hours at 70°F (21°C). Allow
12 hours for Heavy foot traffic. Allow 72 hours before
replacing heavy furniture or opening area to vehicular
traffic at 70°F (21°C). Test area for sealer acceptance
and desired results.
Clean Up
When wet, flush with clean water. When dry, clean tools
and equipment with CT-12 Thinner.
Limitations
- Do not apply if surface temperature is below 40°F (4°C) or is expected to fall below 40°F (4°C) within 24 hours.
- Do not apply if rain is expected within 3 hours of application.
- Do not install on slabs subject to hydrostatic pressure.
- Do not add paint thinners, solvents, or admixtures.
- Do not use in areas subject to constant immersion
- Do not install concrete overlays, other toppings or surface treatments over this material.
Test area for sealer acceptance and desired results.
Health and SafetyBefore using this product consult the Safety DataSheet (SDS). The SDS can be obtained at www.covertecproducts.com
Limited Warranty
This product is warranted to be of good quality and that it complies with the properties shown in its current datasheet. CoverTec will replace or, at our election, refund the purchase price of the product if proven defective when used according to the instructions in the current datasheet. Any suspected defect must be reported to CoverTec in writing within one (1) year from the date of shipment. No claim will be considered without such written notice or after the specified time interval. CoverTec Products LLC. makes no warranty as to the merchantability or fitness for a particular purpose and this warranty is in lieu of all other warranties express or implied and explicitly excludes liability for consequential damages, down time, or delay.
